ST5, ST5-16mm2, ST6 and ST25 Weidmuller, United States 821 Southlake Blvd. Richmond, Virginia 23236 TS 35 12.2/.48 12.2/.48 Rails Part No. Part No. TS 35 steel 0383400000 0383400000 TS 35 steel slotted 0514500000 0514500000 iEc/diN-vdE C US iEc/diN-vdE C US iEc/diN-vdE C US 1.0037 Material St37-2 Steel Equivalent, Composition DIN 17100 St37-2 Steel (1.0037 Material) St37-2 steel (1.0037 material) is an unalloyed structural steel grade complies with DIN 17100:1980 and has been discarded since 2004. According to German standard DIN 17100, St37 steel is divided into St37-2, USt37-2, RSt37-2 and St37-3.
DIN 125 / ISO 7089,7090 A2/A4 Stainless Steel; DIN 125 / ISO 7089,7090 Brass; DIN 126 Bare Steel/Hot Din 1710 St6 2 Steel Din 1710 St6 2 Steel (ISO FIT) DIN 433 Small O.D. Zinc Plated; DIN 433 Small O.D. A2/A4 Stainless Steel; DIN 1440 For Clevis Pins Bare Steel/Zinc Plated; DIN 6916HV-10 Structural Bare Steel/Yellow Zinc Plated; DIN 7349 Thick Zinc Plated DIN 17100 STEELS FOR GENERAL STRUCTURAL PURPOSESPart 4, DIN 1629 Part 1 to part4, DIN 2391 Part2, DIN 2393 part 2, DIN 2394, DIN 2395 Part 2, DIN 2395 part3]. Steel castings (See DIN 1681). Cold rolled flat products without coating (see DIN 1623 Part2, new version in preparation). Flat steel products with coatings(DIN Standards in preparation). Bright finished steel (see DN 1652). DIN 17121 Grade ST52.3 Seamless Tubing ST52-3 NBK A low alloy steel, grade ST52.3 is known to be a high strength material. One of the advantages of using the ST52.3 Tubing is that it is easily welded to other steel grades. Another benefit is its strength properties. The tensile strength for pipes belonging to specification DIN 17121 Grade St52-3 ranges between 490 Mpa to 630 Mpa. Whereas their
DIN 968 Cross recessed Pan Head With washer self-tapping screws, Phillips / Pozi, material by steel or stainless steel etc. DIN ST52-2 Angle Steel - 355 MPa Yield StrengthDIN ST52-2 Angle Steel - Good Weldability. ST52 steel angle with 0.23% carbon content and 355 MPa yield point strength is suitable for weldable & supporting components. According to chemical composition & mechanical property, it is similar to S355N of EN 10025-3. ISO 7049 - Pan head tapping screws with cross recess H and ISO 7049 - Pan head tapping screws with cross recess H and Z, Form C Current norm:DIN ISO 7049 Equivalent norms:DIN 7981 C; CSN 021235; UNI 6954;
The ST6 application is suitable for base point verifications of steel columns clamped in pocketed foundations and exposed to biaxial loading according to EN 1993. The permissible column cross sections are I-shaped steel profiles. The column base is designed as a welded on base plate. Standards - DIN EN 1993 - ÖNORM EN 1993 - BS EN 1993 STAINLESS STEEL LIST OF EQUIVALENCESx 2 crnimo 1712 x 2 crnimo 1713 x 2 crnimo 1713 x 6 crnimoti 1712 x 6 crniti 1811 x6cral 13 x2crti12 x6crti12 x8cr17 x8crmo 17 x20 cr 13 x30 cr 13 x40 cr 14 x16cr ni 16 stainless steel list of equivalences aproximate equivalences list of norms for stainless steel en (europe) aisi uns (usa) afnor (france) bsi (united kingdom) din (germany) gost St12 (DIN, WNr ) - Worldwide equivalent grades - Steel St12 (Germany, DIN, WNr ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt
St12 (Germany, DIN, WNr ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Steel Grades - Foreign Standards . Steel Grade (domestic analogue ) Steel Grade. DIN. Steel Grade. EN. Steel Grade. ASTM. 15Cr3. 17200--5115. A29/A29M. 15H GOST 4543-71. 20Cr4 st 52.3 carbon steel round bar, din 17100 st 52.3 Check once our astm Carbon Steel ST 52.3 bar stock price before buying Carbon Steel ST 52.3 flat bar from India or China. also mail for our live stock of asme ST 52.3 carbon steel bar to check types & sizes with our ready stock we can give you best price of st 52.3 din 17100 material bar
DIN 17100 St 37-2 steel equivalent grade:St 37-2 steel plate/sheet is in DIN 17100 standard, the material number is 1.0037. The equivalent grade of St 37-2 steel are EN 10025 EN 10025, NFA 35-501 E 24-2, UNI 7070 Fe 360 B, BS 4360 40 A, ASTM A 283 C A 570 Gr. 33.
Please Click here